You are here: Home > SPOD Products
Sort By:
Page of 1
spod-500-97
500-97 Jeep Wrangler TJ 1997-2002 6 Switch & Source System By sPOD
List Price: $546.00
Our Price: 455.00
You save $91.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-300-arb
300-ARB Universal Adapter Harness for ARB Compressor By sPOD
List Price: $21.60
Our Price: 18.00
You save $3.60!




Adapter Harness for ARB compressor to utilize sPOD switches and Source to control compressor, front and rear lockers.
!!!! Note !!!!!
This adapter harness is NOT required for the twin ARB compressor if you are not using the compressor for lockers!
All that is required is to attach the 1 purple wire from
the ARB harness to any of the positive outputs on the sPOD's Source.
ARB Adapter Harness
spod-500-03
500-03 Jeep Wrangler TJ 2003-2006 6 Switch & Source System By sPOD
List Price: $546.00
Our Price: 455.00
You save $91.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-03lt-led a
500-03LT-LED A Jeep Wrangler TJ 2003-2006 Amber 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-03lt-led b
500-03LT-LED B Jeep Wrangler TJ 2003-2006 Blue 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-03lt-led g
500-03LT-LED G Jeep Wrangler TJ 2003-2006 Green 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-03lt-led r
500-03LT-LED R Jeep Wrangler TJ 2003-2006 Red 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-830k
500-830k Universal Source Without Switch Bezel By sPOD
List Price: $384.00
Our Price: 320.00
You save $64.00!




Part Number: 500-830K Source Without Switch Bezel
spod-500-97lt-led a
500-97LT-LED A Jeep Wrangler TJ 1997-2002 Amber 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-97lt-led b
500-97LT-LED B Jeep Wrangler TJ 1997-2002 Blue 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-97lt-led g
500-97LT-LED G Jeep Wrangler TJ 1997-2002 Green 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-500-97lt-led r
500-97LT-LED R Jeep Wrangler TJ 1997-2002 Red 6 Switch Dual LED & Source System By sPOD
List Price: $648.00
Our Price: 540.00
You save $108.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Dula light LED Contura switches, (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch (Tyco) cube style relays (SPST 30amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-03
510-03 Jeep Wrangler TJ 2003-2006 6 Switch & Source System W/ Air Gauge By sPOD
List Price: $570.00
Our Price: 475.00
You save $95.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-03lt-led a
510-03LT-LED A Jeep Wrangler TJ 2003-2006 Amber 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-03lt-led b
510-03LT-LED B Jeep Wrangler TJ 2003-2006 Blue 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-03lt-led g
510-03LT-LED G Jeep Wrangler TJ 2003-2006 Green 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-03lt-led r
510-03LT-LED R Jeep Wrangler TJ 2003-2006 Red 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-97
510-97 Jeep Wrangler TJ 1997-2002 6 Switch & Source System W/ Air Gauge By sPOD
List Price: $570.00
Our Price: 475.00
You save $95.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-97lt-led a
510-97LT-LED A Jeep Wrangler TJ 1997-2002 Amber 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-97lt-led b
510-97LT-LED B Jeep Wrangler TJ 1997-2002 Blue 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-97lt-led g
510-97LT-LED G Jeep Wrangler TJ 1997-2002 Green 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-510-97lt-led r
510-97LT-LED R Jeep Wrangler TJ 1997-2002 Red 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, header, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-580-hacp
580-HACP Universal Hi-Amp Circuit Protect Bat Cable By sPOD
List Price: $95.99
Our Price: 79.99
You save $16.00!




The new Hi-Amp Circuit Protection “Option”

With the growing demand for higher current (amperage) and circuit protection, sPOD has designed and engineered a totally new option for the customers that need a higher current capacity with ultimate circuit protection! The existing circuit breaker we supply has a high limit of 50 amps. Our new Hi-Amp Circuit Protection will bring it up to 80 amps! We call it a Duty Safe Breaker. The term Duty Safe comes from the idea that most things that are added to vehicles do not run 100% of the time but when they are running they can draw high currents. So a duty cycle concept for a circuit breaker is needed for these applications.

The benefits of this are:

  • 1) No mechanical parts or contacts to wear out.
  • 2) It’s self-healing so no replacement is required.
  • 3) It will not reset if there is an actual circuit fault.
  • 4) It helps prevent a reset until short is fixed by working thermally.
  • 5) Allows up to 80 amps before shutting off the system.
  • 6) Fully integrated into the positive power cable.

spod-580-hacp-1
580-HACP-1 Universal Hi-Amp Circuit Protect Bat Cable By sPOD
List Price: $54.00
Our Price: 45.00
You save $9.00!




sPOD 580-HACP-1 - Hi-Amp Circuit Protect Bat Cable
spod-600-07
600-07 Jeep Wrangler JK 2007-2008 6 Switch & Source System By sPOD
List Price: $522.00
Our Price: 435.00
You save $87.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector.

NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.


All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
A quick intro to the sPOD system
spod-600-07lt-led a
600-07LT-LED A Jeep Wrangler JK 2007-2008 Amber 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.
spod-600-07lt-led b
600-07LT-LED B Jeep Wrangler JK 2007-2008 Blue 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.
spod-600-07lt-led g
600-07LT-LED G Jeep Wrangler JK 2007-2008 Green 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.
spod-600-07lt-led r
600-07LT-LED R Jeep Wrangler JK 2007-2008 Red 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.
spod-600-0915
600-0915 Jeep Wrangler JK 2009-2015 6 Switch & Source System By sPOD
List Price: $522.00
Our Price: 435.00
You save $87.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi-color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.


NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.



All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-600-0915lt-led a
600-0915LT-LED A Jeep Wrangler JK 2009-2015 Amber 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.


spod-600-0915lt-led b
600-0915LT-LED B Jeep Wrangler JK 2009-2015 Blue 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.


spod-600-0915lt-led g
600-0915LT-LED G Jeep Wrangler JK 2009-2015 Green 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.


spod-600-0915lt-led r
600-0915LT-LED R Jeep Wrangler JK 2009-2015 Red 6 Switch Dual LED Contura Rocker & Source System By sPOD
List Price: $624.00
Our Price: 520.00
You save $104.00!




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Double light LED Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual LED option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch LED colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
  • LED's are much dimmer and less distracting
  • LED's draw much less current
  • LED's have a much longer life span than incandescent lights.


spod-600-mini-07
600-MINI-07 Jeep Wrangler JK 2007-2008 6 Switch W/ 7 Inch Widht Mini Bezel By sPOD
List Price: $522.00
Our Price: 435.00
You save $87.00!




Compatible with 2007 & 2008 JK Models
Will work in River Raider Off-Road Weld in Sport Cage

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.


NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.


All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-610-07
610-07 Jeep Wrangler JK 2007-2008 6 Switch & Source System W/ Air Gauge By sPOD
List Price: $552.00
Our Price: 460.00
You save $92.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.


NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.


All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-610-07lt-led a
610-07LT-LED A Jeep Wrangler JK 2007-2008 Amber 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.

Text composed with the best online HTML editor. Please subscribe for a HTML G membership to remove this message.

spod-610-07lt-led b
610-07LT-LED B Jeep Wrangler JK 2007-2008 Blue 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-610-07lt-led g
610-07LT-LED G Jeep Wrangler JK 2007-2008 Green 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-610-07lt-led r
610-07LT-LED R Jeep Wrangler JK 2007-2008 Red 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-610-0915
610-0915 Jeep Wrangler JK 2009-2015 6 Switch & Source System W/ Air Gauge By sPOD
List Price: $552.00
Our Price: 460.00
You save $92.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.


NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.


All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-610-0915lt-led a
610-0915LT-LED A Jeep Wrangler JK 2009-2015 Amber 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six double light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-610-0915lt-led b
610-0915LT-LED B Jeep Wrangler JK 2009-2015 Blue 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six double light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-610-0915lt-led g
610-0915LT-LED G Jeep Wrangler JK 2009-2015 Green 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six double light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-610-0915lt-led r
610-0915LT-LED R Jeep Wrangler JK 2009-2015 Red 6 Switch Dual LED & Source System W/ Air Gauge By sPOD
List Price: $654.00
Our Price: 545.00
You save $109.00!




Each system includes the following:
All required mounting brackets and hardware. System will come pre-wired ready to install.

Included:
Switch panel, six double light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.
Complete Air Gauge kit 0-200 psi Air Gauge w/Quick Release Camozzi fittings and 10' of high pressure connection line.All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-07
620-07 Jeep Wrangler JK 2007-2008 6 Switch With 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $522.00
Our Price: 435.00
You save $87.00!




Gauge Not included in system.

This panel will not accommodate the new Genesis adapter


If using a Aeroforce Gauge, request their longer harness.




Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.


NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.


All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-620-07lt-led a
620-07LT-LED A Jeep Wrangler JK 2007-2008 Amber 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

This panel will not accommodate the new Genesis adapter


If using a Aeroforce Gauge, request their longer harness.


Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-07lt-led b
620-07LT-LED B Jeep Wrangler JK 2007-2008 Blue 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

This panel will not accommodate the new Genesis adapter


If using a Aeroforce Gauge, request their longer harness.


Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-07lt-led g
620-07LT-LED G Jeep Wrangler JK 2007-2008 Green 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

This panel will not accommodate the new Genesis adapter


If using a Aeroforce Gauge, request their longer harness.


Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-07lt-led r
620-07LT-LED R Jeep Wrangler JK 2007-2008 Red 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

This panel will not accommodate the new Genesis adapter


If using a Aeroforce Gauge, request their longer harness.


Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-0915
620-0915 Jeep Wrangler JK 2009-2015 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included; Won't Work With Genesis Adapter
List Price: $522.00
Our Price: 435.00
You save $87.00!




Gauge Not included in system.
This bezel Does Not accommodate new Genesis Adapter.

If using a Aeroforce Gauge, request their longer harness.

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-620-0915lt-led a
620-0915LT-LED A Jeep Wrangler JK 2009-2015 Amber 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

If using a Aeroforce Gauge, request their longer harness.

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-0915lt-led b
620-0915LT-LED B Jeep Wrangler JK 2009-2015 Blue 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

If using a Aeroforce Gauge, request their longer harness.

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-0915lt-led g
620-0915LT-LED G Jeep Wrangler JK 2009-2015 Green 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

If using a Aeroforce Gauge, request their longer harness.

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-620-0915lt-led r
620-0915LT-LED R Jeep Wrangler JK 2009-2015 Red 6 Switch Dual LED & Source System W/ 2 1/16 Inch Widht Gauge Hole By sPOD - Gauge Not Included
List Price: $624.00
Our Price: 520.00
You save $104.00!




Gauge Not included in system.

If using a Aeroforce Gauge, request their longer harness.

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six Dual LED light Contura switches (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:

  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers

Highlights of the dual light option:

  • Gives the operator a choice of having a nightlighted switch.
  • The lower lighted portion of the switch is fullycontrolled by the operator.
  • Prevents from tapping into the OEMelectrics.
  • Choices of switch actuator colors Red, Green,Blue and Amber.
  • No extra wiring required by the installer orcustomer.
  • The upper light still lights up only when the switchis in the on position.
spod-630-07
630-07 Jeep Wrangler JK 2007-2008 6 Switch & Source System W/ Genesis Adapter By sPOD - G Screen Not Included
List Price: $546.00
Our Price: 455.00
You save $91.00!




Compatible with 2007 & 2008 JK Models
Will work in River Raider Off-Road Weld in Sport Cage

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switch panel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators (installed and pre-wired), two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.


NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.


All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-07lt-led a
630-07LT-LED A Jeep Wrangler JK 2007-2008 Amber 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-07lt-led b
630-07LT-LED B Jeep Wrangler JK 2007-2008 Blue 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-07lt-led g
630-07LT-LED G Jeep Wrangler JK 2007-2008 Green 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-07lt-led r
630-07LT-LED R Jeep Wrangler JK 2007-2008 Red 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-0915
630-0915 Jeep Wrangler JK 2009-2015 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $546.00
Our Price: 455.00
You save $91.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six single light Contura switches, 2 Red, 2 Amber and 2 Green actuators(installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.



NOT RECOMMENDED FOR CUSTOM ROCKERS. Switches do not have lower pilot light.


All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-0915lt-led a
630-0915LT-LED A Jeep Wrangler JK 2009-2015 Amber 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-0915lt-led b
630-0915LT-LED B Jeep Wrangler JK 2009-2015 Blue 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:
All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-0915lt-led g
630-0915LT-LED G Jeep Wrangler JK 2009-2015 Green 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-630-0915lt-led r
630-0915LT-LED R Jeep Wrangler JK 2009-2015 Red 6 Switch Dual LED & Source System W/Genesis Adapter By sPOD - G Screen Not Included
List Price: $642.00
Our Price: 535.00
You save $107.00!




This panel includes the new Genesis adapter to allow you to install the Genesis G Screen.
G Screen not included.

Each system includes the following:

All required mounting brackets and hardware.
System will come pre-wired ready to install.

Included:
Switchpanel, six dual 24v LED Contura rocker switches and push button to turn bottom lights on and off (installed and pre-wired), two piece Wire Harness set with 8 multi colorleads utilizing 18 gauge wires. Each end has an automotive connectormade by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • IntegratedLVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage andwill cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enoughjuice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket for Jeep Wranglers
spod-700-mini
700-Mini 7 in. Mini Switch Panel & Source System With Mini Bezel For Universal Trucks By sPOD
List Price: $522.00
Our Price: 435.00
You save $87.00!




Universal System for use in many trucks and UTVs. This system includes 7"" Mini switch panel. The sPOD switch panel is easy to install and arrives with switches installed and wired for plug and play ease like our Jeep TJ and JK systems. Source mounts to top of fuse box. Minimal cutting and drilling required. Has been installed in Ram 2500 Laramie.

Each system includes the following:
All required mounting brackets and hardware.

Included:
Six Contura switches, 2 Red, 2 Amber and 2 Green actuators, two piece Wire Harness set with 8 multi-color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from ""field collapse""
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
spod-700-mod
700-Mod 6 Switch Panel & Source System With Modular For Universal Trucks By sPOD
List Price: $435.60
Our Price: 363.00
You save $72.60!




Universal System for use in many trucks and UTVs. This system includes a Modular 6 switch panel. The sPOD switch panel is easy to install and arrives with switches installed and wired for plug and play ease like our Jeep TJ and JK systems. Source mounts to top of fuse box. Some cutting and drilling required.

Each system includes the following:
All required mounting brackets and hardware.

Included:
Six Contura switches, 2 Red, 2 Amber and 2 Green actuators, two piece Wire Harness set with 8 multi-color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
Video the includes the installation of the modular switch panel.
spod-700-ram
700-RAM Switch Panel & Source System With Ram Mount For Universal Trucks By sPOD
List Price: $600.00
Our Price: 500.00
You save $100.00!




Universal System for use in many trucks and UTVs. This system includes a 6 switch panel with a 1" Ram Mount Ball. The sPOD switch panel is easy to install and arrives with switches installed and wired for plug and play ease like our Jeep TJ and JK systems. Source mounts to top of fuse box. Since this is mounted with a Ram Mount, the panel can easily be removed and put away when not in use. Minimal cutting and drilling required.

Each system includes the following:
All required mounting brackets and hardware.

Included:
Six Contura switches, 2 Red, 2 Amber and 2 Green actuators, two piece Wire Harness set with 8 multi-color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
spod-700-tun
700-Tun Toyota Tundra 2012-2015 Switch Panel & Source System With Sunglass Holder By sPOD
List Price: $522.00
Our Price: 435.00
You save $87.00!




6 Switch System for use in 2012-2015 Toyota Tundra. This system includes a 6 switch panel which replaces overhead sunglass holder panel. The sPOD switch panel is easy to install and arrives with switches installed and wired for plug and play ease like our Jeep TJ and JK systems. Source mounts to top of fuse box. Minimal cutting and drilling required.

Each system includes the following:
All required mounting brackets and hardware.

Included:
Six Contura switches, 2 Red, 2 Amber and 2 Green actuators, two piece Wire Harness set with 8 multi-color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
Cable routing for the Toyota Tundra sPOD.
spod-8-600-07-led a
8-600-07-LED A Jeep Wrangler JK 2007-2008 Amber 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

·Fully programmable Digital controlled system.
  • Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • Expandable (Daisy Chained select-able) to up to32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • One single ATM mini-style fuse for LVCOprotection and reset.
  • Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • Automatic system shut down when panel isunplugged
  • Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • Lower pilot light has an independent powercontrol push button for full operator control
  • Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2007– 2008) with specific mounting hardware
  • Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • Two ports available integrated into the CAN-Buscontroller.
spod-8-600-07-led b
8-600-07-LED B Jeep Wrangler JK 2007-2008 Blue 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

·Fully programmable Digital controlled system.
  • Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • Expandable (Daisy Chained select-able) to up to32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • One single ATM mini-style fuse for LVCOprotection and reset.
  • Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • Automatic system shut down when panel isunplugged
  • Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • Lower pilot light has an independent powercontrol push button for full operator control
  • Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2007– 2008) with specific mounting hardware
  • Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • Two ports available integrated into the CAN-Buscontroller.
spod-8-600-07-led g
8-600-07-LED G Jeep Wrangler JK 2007-2008 Green 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

·Fully programmable Digital controlled system.
  • Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • Expandable (Daisy Chained select-able) to up to32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • One single ATM mini-style fuse for LVCOprotection and reset.
  • Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • Automatic system shut down when panel isunplugged
  • Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • Lower pilot light has an independent powercontrol push button for full operator control
  • Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2007– 2008) with specific mounting hardware
  • Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • Two ports available integrated into the CAN-Buscontroller.
spod-8-600-07-led r
8-600-07-LED R Jeep Wrangler JK 2007-2008 Red 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

·Fully programmable Digital controlled system.
  • Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • Expandable (Daisy Chained select-able) to up to32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • One single ATM mini-style fuse for LVCOprotection and reset.
  • Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • Automatic system shut down when panel isunplugged
  • Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • Lower pilot light has an independent powercontrol push button for full operator control
  • Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2007– 2008) with specific mounting hardware
  • Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • Two ports available integrated into the CAN-Buscontroller.
spod-8-600-0915-led a
8-600-0915-LED A Jeep Wrangler JK 2009-2015 Amber 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

  • ·Fully programmable Digital controlled system.
  • ·Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • ·Expandable (Daisy Chained selectable) to up to32 circuits with simple plug-n-play features!
  • ·Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • ·No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • ·Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • ·One single ATM mini-style fuse for LVCOprotection and reset.
  • · Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • ·Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • ·Automatic system shut down when panel isunplugged
  • ·Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • ·Lower pilot light has an independent powercontrol push button for full operator control
  • ·Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • ·Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2009– 2015) with specific mounting hardware
  • ·Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • ·Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • ·Two ports available integrated into the CAN-Buscontroller.

-->

spod-8-600-0915-led b
8-600-0915-LED B Jeep Wrangler JK 2009-2015 Blue 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

  • ·Fully programmable Digital controlled system.
  • ·Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • ·Expandable (Daisy Chained selectable) to up to32 circuits with simple plug-n-play features!
  • ·Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • ·No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • ·Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • ·One single ATM mini-style fuse for LVCOprotection and reset.
  • · Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • ·Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • ·Automatic system shut down when panel isunplugged
  • ·Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • ·Lower pilot light has an independent powercontrol push button for full operator control
  • ·Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • ·Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2009– 2015) with specific mounting hardware
  • ·Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • ·Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • ·Two ports available integrated into the CAN-Buscontroller.
spod-8-600-0915-led g
8-600-0915-LED G Jeep Wrangler JK 2009-2015 Green 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

  • ·Fully programmable Digital controlled system.
  • ·Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • ·Expandable (Daisy Chained selectable) to up to32 circuits with simple plug-n-play features!
  • ·Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • ·No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • ·Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • ·One single ATM mini-style fuse for LVCOprotection and reset.
  • · Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • ·Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • ·Automatic system shut down when panel isunplugged
  • ·Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • ·Lower pilot light has an independent powercontrol push button for full operator control
  • ·Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • ·Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2009– 2015) with specific mounting hardware
  • ·Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • ·Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • ·Two ports available integrated into the CAN-Buscontroller.
spod-8-600-0915-led r
8-600-0915-LED R Jeep Wrangler JK 2009-2015 Red 8 Circuit SE System W/ Switch Panel By sPOD
List Price: $864.00
Our Price: 720.00
You save $144.00!




The industry leader in powerand control solutions.


The system utilizes automotive gradeapproved high-power, high-temp, ultra-reliable components with a maximum 100amp capacity! The sPOD SourceSE is a fully programmable digitalCAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware,engineered and 100% manufactured in the United States.

Features:

  • ·Fully programmable Digital controlled system.
  • ·Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminalblock for attaching accessories.
  • ·Expandable (Daisy Chained selectable) to up to32 circuits with simple plug-n-play features!
  • ·Low voltage cutoff (LVCO) battery protectioncircuit has spec voltage cutoff at 11.2 VDC with a two-minute delay beforeshutting down the SourceSE. This is useful when you have accessoriesturned on while the vehicle is not running. When the vehicle starts, the accessories canthen be used again. The low voltage battery protection circuit can be turnedoff with the DIP switches.
  • ·No more worrying about what rated fuse toinstall! The system will protect from 1.5 amps to 30 amps automatically. TheSourceSE incorporates a failsafe self-healing fault protectionsystem. Fuses have been eliminated (forall accessory outputs) and replaced with current-sensing MOSFETs controlled bya microprocessor. This is a greatfeature for low maintenance and troubleshooting
  • ·Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for futureoptional enhancements.
  • ·One single ATM mini-style fuse for LVCOprotection and reset.
  • · Mix-N-Match with the touchscreen.

Switch Panel Features:

The new switch panel has 8 switches. This panel uses an Ethernetcable that interfaces with the Source with a RJ-45 plug on both ends. Standard cable length will be 10 feet.

  • ·Each switch is programmable for Strobe or Flash (by a sequenceof On/Off/On quickly )
  • ·Automatic system shut down when panel isunplugged
  • ·Dual lit (LED indicator lights, ON position& pilot light) in Red, Green, Blue or Amber. (All switches will be one color)
  • ·Lower pilot light has an independent powercontrol push button for full operator control
  • ·Switches are Carling Technologies Contura serieswith an IP67 rating (marine/heavy equipment)
  • ·Switch Panel housing is NOT plastic but rather,an aluminum formed and welded design to match the interior of the Jeep JK (2009– 2015) with specific mounting hardware
  • ·Switch panel can be daisy chained for remoteoperations (EG: one panel in cab and one panel in far back of truck) can easilyadd up to 10 switch panels. Options to mix and match with the Touchscreenpanels as well.
  • ·Selection of up to 4 sPOD SourceSE tohave control of up to 32 circuits.
  • ·Two ports available integrated into the CAN-Buscontroller.
spod-8-700-ts-fj
8-700-TS-FJ Toyota FJ Cruiser 2007-2014 8 Circuit SE System W/ Touchscreen By sPOD - Does Not Include A RAM Base
List Price: $900.00
Our Price: 750.00
You save $150.00!




The industry leader in power and control solutions.
The system utilizes automotive grade approved high-power,high-temp, ultra-reliable components with a maximum 100 amp capacity! The sPODSourceSE is a fully programmable digital CAN-Bus controlled systemutilizing state-of-the-art technologies. OEM vehicle specific simpleinstallation hardware, engineered and 100% manufactured in the United States.

Features:
  • Fullyprogrammable Digital controlled system.
  • Eight circuits rated @30amps@12.5vdcper circuit that are “End-User” friendly terminal block forattaching accessories.
  • Expandable (Daisy Chainedselectable) to up to 32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) batteryprotection circuit has spec voltage cutoff at 11.2 VDC with a two-minutedelay before shutting down theSourceSE. Thisis useful when you have accessories turned on while the vehicle is notrunning. When the vehicle starts, the accessories can then be used again.The low voltage battery protection circuit can be turned off with the DIPswitches.
  • No more worrying about whatrated fuse to install! The system will protect from 1.5 amps to 30 ampsautomatically. The SourceSE incorporates a fail-safe self-healingfault protection system. Fuses have been eliminated (for all accessoryoutputs) and replaced with current-sensing MOSFETs controlled by amicroprocessor. This is a great feature for low maintenance andtroubleshooting
  • Shield receptacle for theoptionalBluetooth module for a plug-n-play end-user upgrade. This creates ascalable platform for future optional enhancements.
  • One single ATM mini-style fusefor LVCO protection and reset.

Touchscreen Control Module Features:

The new touchscreen controller issmall but packs aBIG punch! (3-3/4”w X 2-7/8”h X 5/8” thk) The controlmodule is a 3.5-inch LED backlit TFT LCD screen with a resolution of 320 x 240,16.7m colors and a viewing angle of 180 degrees housed in a billet aluminumcase with a 1” RAM mount installed on back panel. The connection between theSourceSE and the touchscreen uses a small 90 degree 3.5mm standard 4pin audio jack with a RJ-45 Ethernet plug on the SourceSE end.Standard cable length will be 12 feet.

PLEASE NOTE: Touchscreen case includes a 1" RAM mount installed on back panel but does not include a RAM base. Please ADD your RAM mount base option unless you plan to purchase separately.

o Customization: legends (3 lines of text)

· Each switch is programmable for:

o Dimming

o Strobe

o Flash

o Momentary

o Switch Linking

o On Road & Off Road mode of operation

o Multible Source - control up to 32 circuits

·Voltage feedback (vehicle’sbattery/alternator voltage)

·SourceSE boardtemperature feedback (shown on screen)

·Automatic power off after 10 minutesof being inactive

·One touch screen off function

·One second hold on off button shutsall circuits down

·Automatic system shut down whentouchscreen is unplugged

·Touchscreen housing is NOT plasticbut rather, an aluminum billet machined clam-shell designed with several optionsfor mounting

·Two ports for connection; one on topand one on bottom

·Touchscreens can be daisy chainedfor remote operations (EG: one panel in cab and one panel in far back of truck)can easily add up to 3 touchscreens

·Selection of up to 4 sPOD SourceSEto have control of up to 32 circuits. (DIP switch selectable)

spod-8-700-ts-jk
8-700-TS-JK Jeep Wrangler JK 2007-2015 8 Circuit SE System W/ Touchscreen By sPOD
List Price: $900.00
Our Price: 750.00
You save $150.00!





The industry leader in power and control solutions.
The system utilizes automotive grade approved high-power, high-temp, ultra-reliable components with a maximum 100 amp capacity! The sPOD SourceSE is a fully programmable digital CAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware, engineered and 100% manufactured in the United States.

Features:

  • · Fully programmable Digital controlled system.
  • · Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminal block for attaching accessories.
  • · Expandable (Daisy Chained selectable) to up to 32 circuits with simple plug-n-play features!
  • · Low voltage cutoff (LVCO) battery protection circuit has spec voltage cutoff at 11.2 VDC with a two-minute delay before shutting down the SourceSE. This is useful when you have accessories turned on while the vehicle is not running. When the vehicle starts, the accessories can then be used again. The low voltage battery protection circuit can be turned off with the DIP switches.
  • · No more worrying about what rated fuse to install! The system will protect from 1.5 amps to 30 amps automatically. The SourceSE incorporates a failsafe self-healing fault protection system. Fuses have been eliminated (for all accessory outputs) and replaced with current-sensing MOSFETs controlled by a microprocessor. This is a great feature for low maintenance and troubleshooting
  • · Shield receptacle for theoptional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for future optional enhancements.
  • · One single ATM mini-style fuse for LVCO protection and reset.

Touchscreen Control Module Features:

The new touchscreen controller is small but packs a BIG punch! (3-3/4”w X 2-7/8”h X 5/8” thk) The control module is a 3.5-inch LED backlit TFT LCD screen with a resolution of 320 x 240, 16.7m colors and a viewing angle of 180 degrees housed in a billet aluminum case with a 1” RAM mount installed on back panel. The connection between the SourceSE and the touchscreen uses a small 90 degree 3.5mm standard 4 pin audio jack with a RJ-45 Ethernet plug on the SourceSE end. Standard cable length will be 12 feet.

· Customization: legends (3 lines of text)

Each switch is programmable for:

o Dimming

o Strobe

o Flash

o Momentary

o Switch Linking

o On Road & Off Road mode of operation

o Multible Source control up to 32 circuits

· Voltage feedback (vehicle’s battery/alternator voltage)

· SourceSE board temperature feedback (shown on screen)

· Automatic power off after 10 minutes of being inactive

· One touch screen off function

· One second hold on off button shuts all circuits down

· Automatic system shut down when touchscreen is unplugged

· Touchscreen housing is NOT plastic but rather, an aluminum billet machined clam-shell designed with several options for mounting

· Two ports for connection; one on top and one on bottom

· Touchscreens can be daisy chained for remote operations (EG: one panel in cab and one panel in far back of truck) can easily add up to 3 touchscreens

· Selection of up to 4 sPOD SourceSE to have control of up to 32 circuits. (DIP switch selectable)

spod-8-700-ts-tac
8-700-TS-TAC Toyota Tacoma 2005-2012 8 Circuit SE System W/ Touchscreen By sPOD
List Price: $900.00
Our Price: 750.00
You save $150.00!




The industry leader in power and control solutions.
The system utilizes automotive grade approved high-power,high-temp, ultra-reliable components with a maximum 100 amp capacity! The sPODSourceSE is a fully programmable digital CAN-Bus controlled systemutilizing state-of-the-art technologies. OEM vehicle specific simpleinstallation hardware, engineered and 100% manufactured in the United States.

Features:

  • Fullyprogrammable Digital controlled system.
  • Eight circuits rated @30amps@12.5vdc per circuit that are “End-User” friendly terminal block forattaching accessories.
  • Expandable (Daisy Chainedselectable) to up to 32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) batteryprotection circuit has spec voltage cutoff at 11.2 VDC with a two-minutedelay before shutting down the SourceSE. Thisis useful when you have accessories turned on while the vehicle is notrunning. When the vehicle starts, the accessories can then be used again.The low voltage battery protection circuit can be turned off with the DIPswitches.
  • No more worrying about whatrated fuse to install! The system will protect from 1.5 amps to 30 ampsautomatically. The SourceSE incorporates a failsafe self-healingfault protection system. Fuses have been eliminated (for all accessoryoutputs) and replaced with current-sensing MOSFETs controlled by amicroprocessor. This is a great feature for low maintenance andtroubleshooting
  • Shield receptacle for theoptionalBluetooth module for a plug-n-play end-user upgrade. This creates ascalable platform for future optional enhancements.
  • One single ATM mini-style fusefor LVCO protection and reset.

Touchscreen Control Module Features:

The new touchscreen controller issmall but packs a BIG punch! (3-3/4”w X 2-7/8”h X 5/8” thk) The controlmodule is a 3.5-inch LED backlit TFT LCD screen with a resolution of 320 x 240,16.7m colors and a viewing angle of 180 degrees housed in a billet aluminumcase with a 1” RAM mount installed on back panel. The connection between theSourceSE and the touchscreen uses a small 90 degree 3.5mm standard 4pin audio jack with a RJ-45 Ethernet plug on the SourceSE end.Standard cable length will be 12 feet.

PLEASE NOTE: Touchscreen case includes a 1" RAM mount installed on back panel but does not include a RAM base. Please ADD your RAM mount base option unless you plan to purchase separately.

o Customization: legends (3 lines oftext)

Each switch is programmable for:

o Dimming

o Strobe

o Flash

o Momentary

o Switch Linking

o On Road & Off Road mode of operation

o Multible Source control up to 32 circuits

·Voltage feedback (vehicle’sbattery/alternator voltage)

·SourceSE boardtemperature feedback (shown on screen)

·Automatic power off after 10 minutesof being inactive

·One touch screen off function

·One second hold on off button shutsall circuits down

·Automatic system shut down whentouchscreen is unplugged

·Touchscreen housing is NOT plasticbut rather, an aluminum billet machined clam-shell designed with several optionsfor mounting

·Two ports for connection; one on topand one on bottom

·Touchscreens can be daisy chainedfor remote operations (EG: one panel in cab and one panel in far back of truck)can easily add up to 3 touchscreens

·Selection of up to 4 sPOD SourceSEto have control of up to 32 circuits. (DIP switch selectable)

spod-8-700-ts-tac_2
8-700-TS-TAC Toyota Tundra 2005-2012 9 Circuit SE System W/ Touchscreen By sPOD
List Price: $900.00
Our Price: 750.00
You save $150.00!




The industry leader in power and control solutions.
The system utilizes automotive grade approved high-power,high-temp, ultra-reliable components with a maximum 100 amp capacity! The sPODSourceSE is a fully programmable digital CAN-Bus controlled systemutilizing state-of-the-art technologies. OEM vehicle specific simpleinstallation hardware, engineered and 100% manufactured in the United States.

Features:

  • Fullyprogrammable Digital controlled system.
  • Eight circuits rated @30amps@12.5vdc per circuit that are “End-User” friendly terminal block forattaching accessories.
  • Expandable (Daisy Chainedselectable) to up to 32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) batteryprotection circuit has spec voltage cutoff at 11.2 VDC with a two-minutedelay before shutting down the SourceSE. Thisis useful when you have accessories turned on while the vehicle is notrunning. When the vehicle starts, the accessories can then be used again.The low voltage battery protection circuit can be turned off with the DIPswitches.
  • No more worrying about whatrated fuse to install! The system will protect from 1.5 amps to 30 ampsautomatically. The SourceSE incorporates a failsafe self-healingfault protection system. Fuses have been eliminated (for all accessoryoutputs) and replaced with current-sensing MOSFETs controlled by amicroprocessor. This is a great feature for low maintenance andtroubleshooting
  • Shield receptacle for theoptionalBluetooth module for a plug-n-play end-user upgrade. This creates ascalable platform for future optional enhancements.
  • One single ATM mini-style fusefor LVCO protection and reset.

Touchscreen Control Module Features:

The new touchscreen controller issmall but packs a BIG punch! (3-3/4”w X 2-7/8”h X 5/8” thk) The controlmodule is a 3.5-inch LED backlit TFT LCD screen with a resolution of 320 x 240,16.7m colors and a viewing angle of 180 degrees housed in a billet aluminumcase with a 1” RAM mount installed on back panel. The connection between theSourceSE and the touchscreen uses a small 90 degree 3.5mm standard 4pin audio jack with a RJ-45 Ethernet plug on the SourceSE end.Standard cable length will be 12 feet.

PLEASE NOTE: Touchscreen case includes a 1" RAM mount installed on back panel but does not include a RAM base. Please ADD your RAM mount base option unless you plan to purchase separately.

o Customization: legends (3 lines oftext)

Each switch is programmable for:

o Dimming

o Strobe

o Flash

o Momentary

o Switch Linking

o On Road & Off Road mode of operation

o Multible Source control up to 32 circuits

·Voltage feedback (vehicle’sbattery/alternator voltage)

·SourceSE boardtemperature feedback (shown on screen)

·Automatic power off after 10 minutesof being inactive

·One touch screen off function

·One second hold on off button shutsall circuits down

·Automatic system shut down whentouchscreen is unplugged

·Touchscreen housing is NOT plasticbut rather, an aluminum billet machined clam-shell designed with several optionsfor mounting

·Two ports for connection; one on topand one on bottom

·Touchscreens can be daisy chainedfor remote operations (EG: one panel in cab and one panel in far back of truck)can easily add up to 3 touchscreens

·Selection of up to 4 sPOD SourceSEto have control of up to 32 circuits. (DIP switch selectable)

spod-8-700-ts-tj
8-700-TS-TJ Jeep Wrangler TJ 1997-2006 8 Circuit SE System W/ Touchscreen By sPOD
List Price: $900.00
Our Price: 750.00
You save $150.00!




The industry leader in power and control solutions.
The system utilizes automotive grade approved high-power,high-temp, ultra-reliable components with a maximum 100 amp capacity! The sPODSourceSE is a fully programmable digital CAN-Bus controlled systemutilizing state-of-the-art technologies. OEM vehicle specific simpleinstallation hardware, engineered and 100% manufactured in the United States.

Features:

  • Fullyprogrammable Digital controlled system.
  • Eight circuits rated @30amps@12.5vdc per circuit that are “End-User” friendly terminal block forattaching accessories.
  • Expandable (Daisy Chainedselectable) to up to 32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) batteryprotection circuit has spec voltage cutoff at 11.2 VDC with a two-minutedelay before shutting down the SourceSE. Thisis useful when you have accessories turned on while the vehicle is notrunning. When the vehicle starts, the accessories can then be used again.The low voltage battery protection circuit can be turned off with the DIPswitches.
  • No more worrying about whatrated fuse to install! The system will protect from 1.5 amps to 30 ampsautomatically. The SourceSE incorporates a failsafe self-healingfault protection system. Fuses have been eliminated (for all accessoryoutputs) and replaced with current-sensing MOSFETs controlled by amicroprocessor. This is a great feature for low maintenance andtroubleshooting
  • Two circuits (switches 1 and 2)have the option to be activated by an ignition switched power source(great for accessories that you DO NOT WANT to turn on unless the ignitionkey is on). These two circuits can be easily changed to this option by asimple DIP switch setting on the SourceSE andrunning a jumper wire to tap into a fuse that is only activated when theignition is on. The same two circuits can also be used as High-Beamactivated circuits by tapping into the input side of one of theheadlight’s high-beam circuits. We have taken care of the PWM issue withthe headlight circuits.
  • Shield receptacle for theoptionalBluetooth module for a plug-n-play end-user upgrade. This creates ascalable platform for future optional enhancements.
  • One single ATM mini-style fusefor LVCO protection and reset.

Touchscreen Control Module Features:

The new touchscreen controller issmall but packs a BIG punch! (3-3/4”w X 2-7/8”h X 5/8” thk) The controlmodule is a 3.5-inch LED backlit TFT LCD screen with a resolution of 320 x 240,16.7m colors and a viewing angle of 180 degrees housed in a billet aluminumcase with a 1” RAM mount installed on back panel. The connection between theSourceSE and the touchscreen uses a small 90 degree 3.5mm standard 4pin audio jack with a RJ-45 Ethernet plug on the SourceSE end.Standard cable length will be 12 feet.

PLEASE NOTE: Touchscreen case includes a 1" RAM mount installed on back panel but does not include a RAM base. Please ADD your RAM mount base option unless you plan to purchase separately.

o Customization: legends (3 lines of text)

Each switch is programmable for:

o Dimming

o Strobe

o Flash

o Momentary

o Switch Linking

o On Road & Off Road mode of operation

o Multible Source control up to 32 circuits

·Voltage feedback (vehicle’sbattery/alternator voltage)

·SourceSE boardtemperature feedback (shown on screen)

·Automatic power off after 10 minutesof being inactive

·One touch screen off function

·One second hold on off button shutsall circuits down

·Automatic system shut down whentouchscreen is unplugged

·Touchscreen housing is NOT plasticbut rather, an aluminum billet machined clam-shell designed with several optionsfor mounting

·Two ports for connection; one on topand one on bottom

·Touchscreens can be daisy chainedfor remote operations (EG: one panel in cab and one panel in far back of truck)can easily add up to 3 touchscreens

·Selection of up to 4 sPOD SourceSEto have control of up to 32 circuits. (DIP switch selectable)

Source bracket infromation and usage.
spod-8-700-ts-uni
8-700-TS-8 Circuit SE System W/ Touchscreen For Universal Trucks By sPOD
List Price: $900.00
Our Price: 750.00
You save $150.00!




The industry leader in power and control solutions.
The system utilizes automotive grade approved high-power, high-temp, ultra-reliable components with a maximum 100 amp capacity! The sPOD SourceSE is a fully programmable digital CAN-Bus controlled system utilizing state-of-the-art technologies. OEM vehicle specific simple installation hardware, engineered and 100% manufactured in the United States.

Features:

  • Fully programmable Digital controlled system.
  • Eight circuits rated @30amps @12.5vdc per circuit that are “End-User” friendly terminal block for attaching accessories.
  • Expandable (Daisy Chained selectable) to up to 32 circuits with simple plug-n-play features!
  • Low voltage cutoff (LVCO) battery protection circuit has spec voltage cutoff at 11.2 VDC with a two-minute delay before shutting down the SourceSE. This is useful when you have accessories turned on while the vehicle is not running. When the vehicle starts, the accessories can then be used again. The low voltage battery protection circuit can be turned off with the DIP switches.
  • No more worrying about what rated fuse to install! The system will protect from 1.5 amps to 30 amps automatically. The SourceSE incorporates a failsafe self-healing fault protection system. Fuses have been eliminated (for all accessory outputs) and replaced with current-sensing MOSFETs controlled by a microprocessor. This is a great feature for low maintenance and troubleshooting
  • Shield receptacle for the optional Bluetooth module for a plug-n-play end-user upgrade. This creates a scalable platform for future optional enhancements.
  • One single ATM mini-style fuse for LVCO protection and reset.

Touchscreen Control Module Features:

The new touchscreen controller is small but packs a BIG punch! (3-3/4”w X 2-7/8”h X 5/8” thk) The control module is a 3.5-inch LED backlit TFT LCD screen with a resolution of 320 x 240, 16.7m colors and a viewing angle of 180 degrees housed in a billet aluminum case with a 1” RAM mount installed on back panel. The connection between the SourceSE and the touchscreen uses a small 90 degree 3.5mm standard 4 pin audio jack with a RJ-45 Ethernet plug on the SourceSE end. Standard cable length will be 12 feet.

PLEASE NOTE: Touchscreen case includes a 1" RAM mount installed on back panel but does not include a RAM base. Please ADD your RAM mount base option unless you plan to purchase separately.

o Customization: legends (3 lines of text)

Each switch is programmable for:

o Dimming

o Strobe

o Flash

o Momentary

o Switch Linking

o On Road & Off Road mode of operation

o Multible Source control up to 32 circuits

· Voltage feedback (vehicle’s battery/alternator voltage)

· SourceSE board temperature feedback (shown on screen)

· Automatic power off after 10 minutes of being inactive

· One touch screen off function

· One second hold on off button shuts all circuits down

· Automatic system shut down when touchscreen is unplugged

· Touchscreen housing is NOT plastic but rather, an aluminum billet machined clam-shell designed with several options for mounting

· Two ports for connection; one on top and one on bottom

· Touchscreens can be daisy chained for remote operations (EG: one panel in cab and one panel in far back of truck) can easily add up to 3 touchscreens

· Selection of up to 4 sPOD SourceSE to have control of up to 32 circuits. (DIP switch selectable)

spod-800-000-000
800-000-000 Toyota Tacoma 2005-2012 6 Switches Without Switch Panel By sPOD
List Price: $414.00
Our Price: 345.00
You save $69.00!




2005 – 2012 Model Tacomas do not require a switch panel. The sPOD switches and
wire harness utilize the existing dash/console switch blanks giving a professional OEM appearance.
Six multi-colored Contura switches are provided.

Each system includes the following:
All required mounting brackets and hardware.

Included:
Six Contura switches, 2 Red, 2 Amber and 2 Green actuators, two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
Video the includes the installation of the modular switch panel.
spod-900-000-200
900-000-200 Toyota FJ Cruiser 2007-2014 6 Switches Without Switch Panel By sPOD
List Price: $414.00
Our Price: 345.00
You save $69.00!




FJ Cruisers do not require a switch panel. The sPOD switches and
wire harness utilize the existing dash/console switch blanks giving a professional OEM appearance.
Six multi-colored Contura switches are provided.

Each system includes the following:
All required mounting brackets and hardware.

Included:
Six Contura switches, 2 Red, 2 Amber and 2 Green actuators, two piece Wire Harness set with 8 multi color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
spod-900-fj
900-FJ Toyota FJ Cruiser 2007-2014 6 Switches With Switch Panel By sPOD
List Price: $534.00
Our Price: 445.00
You save $89.00!




FJ Cruisers now have the option of a switch panel. The new sPOD switch panel is easy to install and arrives with switches installed and wired for plug and play ease like our Jeep TJ and JK systems. Minimal cutting and drilling required.

Each system includes the following:
All required mounting brackets and hardware.

Included:
Six Contura switches, 2 Red, 2 Amber and 2 Green actuators, two piece Wire Harness set with 8 multi-color leads utilizing 18 gauge wires. Each end has an automotive connector made by Deutsch.

All wires are wrapped in high temp abrasion resistant nylon braided sleeving.

The Source 6 Circuit power distribution system includes:
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
spod-actuator-removal-tool
Actuator-Removal-Tool Universal Actuator Removal Tool By sPOD
List Price: $4.80
Our Price: 4.00
You save $0.80!




Actuator Removal Tool for Carling Switches
spod-legends-labels
Legends-Labels Universal Stickers To Identify Switches By sPOD
List Price: $9.00
Our Price: 7.50
You save $1.50!




White Vinyl Weatherproof with matte laminate coating, solid black background with white lettering. 49 labels per sheet.
spod-modular 6
Modular 6 Universal Modular Bezel For 6 Switches By sPOD - Not Compatible With New SE Special Edition
List Price: $21.60
Our Price: 18.00
You save $3.60!




#Modular 6 - Switch Panel
spod-rcpm
RCPM Universal Remote Control Power Module For 6 Circuit Source System ONLY By sPOD
List Price: $215.94
Our Price: 179.95
You save $35.99!




Note that the RCPM will NOW work with Samsung phones that have KitKat 4.4.4 or Lollypop 5.0 or higher!


  • Utilizing Bluetooth 4.0 Smart with a general range of up to 25 feet. Distance may vary depending on surrounding.
  • Automatic pairing with smart phone, or PIN invoked pairing
  • Added security using a PIN. Giving it a unique PIN will privatize you’re RCPM.
  • System override for added protection with built in safety override features
  • Compatible iOs 6.3 or newer and Android KitKat 4.4.4 or Lollypop 5.0 or higher newer.
  • Allows full control of the sPOD power distribution system wirelessly using most smart phones
  • Ability to control, switch On/Off, electrical accessories normally switched on and off by the sPOD switch panel mounted inside the vehicle somewhere VIA any smart phone
  • Customizable switch colors, on graphical interface on smart phone, to match your switch panel
  • Customizable switch labeling on graphical interface on smart phone.
  • The kit includes three items: Transceiver and Interface cable. Free downloadable APP from any app store VIA the smart phone.
  • Switching can be set at Momentary or On/Off

  • The RCPM is not compatible with all Samsung phones!!!

    Compatible with Gen II Source system. Upgrade required if you have a Gen I at this time.


    Compatible with iOs 6.3 or newer and Android 4.3 or newer. The apps will only work with these versions and newer.

spod-scs
SCS Universal 6 Switch All-In-One System By sPOD
List Price: $438.00
Our Price: 365.00
You save $73.00!




This self contained system is very compact (8"W x 8"L x 3"H) and is a
turn-key solution for power/switch control for:
  • Utility Trucks/Vehicles
  • Trailers
  • Chase Trucks
  • Recreational Vehicles
  • Camping Trailers
  • Work truck beds with tool boxes
  • Expedition Trailers/Vehicles
Made in the U.S.A.!
Easy to install! (Comes fully wired and integrated. No assembly required!!)
Two battery cables and 4 holes required for mounting using supplied 1/4-20 hardware.
No wiring required, no messing around with switches, relays, fuses and cable routing!
Easy access to add your accessories & just a phillips head screwdriver is all that is needed to
attach your accessories! Toss the relay, switch and fuse that comes with the electrical
accessory and just attach the positive and negative wires to any of the 6 outputs on our
Source, flip a switch and you're done!

The Self contained system 6 Circuit power distribution system includes:
  • 6 single incandescent lighted switches (SPST only)
  • Heavy duty mounting bracket which is made of 14 GA. C.R.S., formed, welded and powder-coated
  • 12 position terminal block for accessory attachment
  • 6 Bosch style cube style relays (SPST 40amp) (plug-in style)
  • 6 ATO style automotive fuses 3 15 amp and 3 30 amp supplied
  • 6 Diodes to protect sensitive accessories such as LED lights from "field collapse"
  • Inline 50amp manual resetting circuit breaker
  • 8 gauge power leads with crimped and soldered terminal for connection to the battery
  • Integrated LVCO (Low-Voltage-Cut-Off) circuit that detects the battery voltage and will cut-off at 10.6VDC and cuts-back in at 12.4VDC so there is enough juice to start your vehicle in case you left an accessory on!!!
  • Fuse for LVCO which can be removed to bypass the LVCO
  • Mounting bracket with hardware (paper drill template included)
spod-tool-bag
Tool-Bag Universal Tool Bag By sPOD
List Price: $38.40
Our Price: 32.00
You save $6.40!




Black tool bag with embroidered sPOD logo. Zippered large main pocket with 2 outside pocket with Velcro closure. 13" x 8" x 8"